ERRIS
Engage in the Romanian Research Infrastructures System
 
Last Update: 31.12.2014
Infrastructure direct public link in ERRIS:
VISITS
REVIEW(S)
SCIENTIFIC & TECHNICAL TEAM:
cordPicture.jpg
Coordinator:

CONTACT:
Phone:
Fax:
Zip code:
Address: , ,
,
RESEARCH SERVICES:
•  Monitoring water quality of irrigation sources with data transmission via GSM to a dispatcher point
•  Providing technical solutions for recovery of rainfall water for irrigation in greenhouses
•  Conducting tests on soil and water quality
•  Monitoring the chemical structure of groundwater in areas vulnerable to pollution
•  Testing modular laser systems in laboratory conditions
•  Theoretical and applied research on pneumatic proportional equipment
•  Research on promoting pneumatic servo equipment and systems
•  Research on systematizing and developing pneumatic sensors
•  Research on means and techniques for adjusting, multiplying and maintaining constant the air pressure in pneumatic systems
•  Research on developing high-efficiency equipment used in vacuum technology
•  Studies and research on developing torque transducers compatible with pneumatic drives
•  Studies and research on pneumatic transport and gravimetric sorting of non-ferrous waste in form of short chips for recycling
•  Theoretical and experimental research on functional optimization of pressure multiplying by low-cost solutions
•  Research on energy optimization for compressed air distribution networks
•  Studies, methodologies and methods for advanced research on the behaviour of pneumatic drive systems using medium and high pressure pneumatic actuators, in order to improve dynamic and power performance
•  Performing computerized quality tests on pneumatic railway wagon valves
•  Theoretical and applied research on pneumatic handling equipment and industrial robots
•  Functional static and dynamic testing of fixed (industrial) and mobile (towed vehicles and motor vehicles) equipment
•  Simulations of typical equipment operating modes
•  Testing in order to determine the performance parameters of various sub-components of systems / equipment that use hydrostatic transmissions for power transmission drive or propulsion
•  Checking pressure and achieving pressure control relays
•  Checking volumetric efficiency of gear pumps
•  Checking the tightness of the inner progressive dispensers
•  Measuring the flow in pressurized circular pipes by using various types of devices (flow sensors, flow transducers, diaphragms, etc.)
•  Measuring flow rates in pipelines of circular cross section on the didactic stand
•  Measuring switching forces occurring in distribution equipment
•  Applied research and experimental testing in the field of Fluid Power for rotary hydraulic machines (pumps and motors)
•  Applied research and experimental testing in the field of Fluid Power for hydraulic parts and equipment
•  Determination of control characteristic of proportional pressure valves
•  Determination of control characteristic of electro-hydraulic proportional directional valves
•  Determination of control characteristic of servo valves
•  Determination of frequency response for electro-hydraulic proportional directional valves
•  Determination of frequency response for servo valves
•  Determining the response to step signal for electro-hydraulic proportional directional valves
•  Determining the response to step signal for servo valves
•  Testing and tuning control loops for hydraulic actuators (cylinders and rotary motors)
•  Computer Aided Design for electronic / electric schemes
•  Simulation of electronic schemes
•  Development of computer-assisted layouts for electronic modules
•  Development of logic blocks with relays or programmable automation logic for electric automations of applications at low voltages
•  Research and physical development of ecology (environmental management) equipment
EQUIPMENTS:
•  1. Equipment for monitoring water quality at the irrigation source
•  2. Equipment for measuring flow in drainage tubes
•  3. System for data acquisition, storage, processing and transmission
•  4. Measure and control instruments
•  5. Modular laser equipment TOPCON for execution and control of levelling works of agricultural lands
•  6. Stand for testing components, subsystems and conventional pneumatic systems with control and analogical display of working parameters
•  7. Testing device for medium and high pressure pneumatic linear actuators
•  8. Pneumatic robot
•  9. Monitoring system
•  10. Compressors
•  11. System for determining fluid properties
•  12. Pneumatic flow meter, brand Kurz (USA), TYPE 504 FT-8
•  13. Modular aggregate for instrumental air preparation, Code AMAI-2.25/16.4
•  14. Electropneumatic positioners
•  15. Pneumatic cylinders
•  16. Mechatronic stand adapted to testing of energy recovery systems
•  17. Mechatronic equipment for the recovery of braking energy
•  18. 3D printer kit
•  19. Testing stand for the components of lubrication systems with data acquisition system
•  20. Equipment for hydrostatic radial bearings
•  21. Equipment for hydrostatic axial bearings
•  22. Equipment for research of the lubrication of linear sealing systems
•  23. Demonstrative panel of the automatic lubrication installation with 2 lines
•  24. Demonstrative panel of the automatic lubrication installation with volumic dosage
•  25. Demonstrative panel of the automatic lubrication facility with progressive dosing
•  26. Demonstrative panel of the automatic lubrication facility by recirculation with electronic monitoring
•  27. LCM 20
•  28. Brookfield digital viscometer
•  29. GPM Manual pressure generator
•  30. Didactic stand for pressures, flow and speed rates
•  31. Device for measuring switching forces on some distribution equipment
•  32. Motic BA 300 microscope
•  33. SELECTA VB 1423 Viscometer Bath
•  34. Stand for applied research and experimental testing of hydraulic rotary machines
•  35. Stand (I) for applied research and experimental testing of hydraulic parts and equipment
•  36. Stand (II) for applied research and experimental testing of hydraulic parts and equipment
•  37. High pressure stand for applied research and experimental testing of hydraulic parts and equipment
•  38. Stand for testing proportional electromagnets
•  39. Stand for testing hydraulic dampers
•  40. Gravimetric dosing system - Equipment for blended wines
•  41. SR780 — 100kHz two-channel dynamic signal analyzer
•  42. TEKTRONIX DPO3014 Oscilloscope
•  43. Stand for testing electro-hydraulic adjusting equipment in static and dynamic regime
•  44. Programmable power supply
•  45. Arbitrary/Function Generator
•  46. Data acquisition board
•  47. Soldering / Desoldering Station
•  48. Measuring amplifier in desktop housing
•  49. Service case with test unit for servo & proportional valves with embedded electronics
•  50. SensoControl Diagnostic kit
•  51. Testing stand of electro-hydraulic adjustment elements in static and dynamic operating modes
•  52. 4 column type vulcanizing press
•  53. Set of moulds for seal vulcanization
•  54. Tensile testing equipment for rubber test specimens and plastic products
•  55. Analytical balance TMI-XA 310
•  56. Drying oven
•  57. Device for measuring the phreatic level in hydrogeological wells
•  58. Stand for testing hydraulic equipment / devices on water
•  59. Double diaphragm dosing pump with hydraulic control - Experimental model
•  60. Double diaphragm dosing pump with mechano-hydraulic control - Prototype
• 
•  61. Stand for digital hydraulics
•  62. Stand for testing parameters in obtaining pellets and briquettes by pressing
REVIEWS:

Latest Reviews


[T: 1.2267, O: 1070]